Research into elements of the multifunctional deformation zones of a car body/Automobilio kebulo daugiafunkciu deformaciniu zonu elementu tyrimas.

Sapragonas, J. ; Juodvalkis, D. ; Makaras, R. 等

1. Introduction

Designing of the new products in automotive industry often involves taking into consideration specific criteria set for vehicles besides general ones such as functionality, and operating costs to price ratio. Recently, the efforts focused on the groups of criteria regulating sustainable development of transportation system, namely energy consumption, environmental pollution, general safety of motor vehicles with respect to crew and environment. Each of these groups had influenced the methodology used for designing car body, and have required for comprehensive theoretical and practical studies. In automobiles, the spatial thin-walled profile structures covered with the shell-type components ensuring the best quality/mass ratio are used as structural elements of a car body [1]. This has initiated intensive both theoretical and applicable studies.

The calculation techniques of thin-walled profiles applied by S. P. Timoschenko [2] for estimation of the strength and consistency in range of elasticity, have been further extended by theoretical and applicable studies to include plastic deformations under dynamic loads [3-5]. The characteristics of elements with the predictive course of plastic deformations have been found, and it has enabled to use some components performing a function of supporting structures as the deformable components within safety zones [6, 7]. After the improved and more precise methodologies for the assessment of component strength and stiffness became available, gradually, by designing the support structures, multifunctional components came into use, for example, elements of chassis and other structures were used as the energy absorbing elements of deformation zones. The necessity to optimize the structure according to many contradictory criteria made automotive manufacturers to develop complex software packages which in turn reduced chances for minor companies to take part in the process of designing and development.

Currently, a trend towards use of an extra criterion is observed, namely--a customer satisfaction/price. Use of the latter criterion is associated with the individualization of a car by distinguishing it from mass produced serial vehicles. It provides small companies with good opportunities. Individualization potentially includes a vast field of needs, and modern technologies, including smart materials and smart technologies, can be currently used by small companies as well. Simultaneously, the designer should allow the user to asses to what extent his/her needs can be satisfied. When recovering old structures the user, knowing that old structures are unable to ensure safety, should be informed about structural and technological possibilities and the price of desired result in order to better assess the risks in comparison with modern systems. Advanced and universal software packages allow for designing car bodies using generalized characteristics, by satisfying customer's order more completely and increasing competitiveness.

This paper involves examination of operating conditions of replaceable elements of frontal safety deformation zones, and influence of individual elements in absorption of impact energy, while determining qualities of these elements based on generalized deformational characteristics. The objective of the research is to investigate the influence of the changes in characteristics of multifunctional elements and introduction of additional elements on the dynamic processes of impact within deformation zones under consideration.

2. The dynamic model of frontal deformation zone

Modern software packages allow for assessment of car body deformations, however for the purpose of preliminary evaluation, simpler models are more handy that allow for more precise specification of interaction among individual deformation zones, and influence of the replaced or additional structural components. Using simple dynamic models makes it possible to readily examine possibilities of the structure. Such models are made based on the principle of multidimensional mechanic systems, and are currently used for the assessment of the effect of individual elements within complex safety system. Principles of formulating models are provided in Ni, C. M.; Song, J. O. [8].

The model under consideration here provides for a three-mass dynamic system with nonlinear elastically plastically deformed elements (Fig. 1). A three-mass dynamic model is one of the simplest however sufficiently precisely reflecting key features of a car's frontal deformation zone.

The deformation zone under consideration in the model is divided into three sections as follows: zone 1 bumper zone ranging from bumper to radiator; zone 2--the engine zone ranging from the radiator to the engine; zone 3 -the car body zone including the space between the engine and car interior front panel. Such a partition of the model into three zones is conditional. Each section reflects a particular zone that includes units present within this zone.

[FIGURE 1 OMITTED]

The behaviour of the model is described using differential equations:

[MATHEMATICAL EXPRESSION NOT REPRODUCIBLE IN ASCII]. (1)

For the purpose of calculations a program was developed based on the computer applications previously developed in the Department of Transport Engineering of Kaunas University of Technology for simulation of the shock impact. Description of nonlinear elastically plastic elements [c.sub.1], [c.sub.2] and [c.sub.3] uses generalized, experimentally established load-deformation relationships (Fig. 2).

[FIGURE 2 OMITTED]

Modern car energy absorbing elements use deformation elements of the following two types--the elements with uniform cross sections with lost local consistency undergo deformation under constant load (Fig. 2, curve 3). Deformation happens in the same way for different foam plastics used in energy absorbing elements. The elements with non-uniform cross section or variable wall thickness undergo deformation by progressively increasing the force, required for their plastic deformation (Fig. 2, curve 4).

Formerly, the elements used in deformation zones also featured a partially inversed relationship--upon loss of consistency, the load decreased and only afterwards reached stabilization. Experimental findings reflect specific patterns of local deformations development--the process is not absolutely consistent (Fig. 2, curve 1).

Deformation characteristics of individual elements can also be predicted using FEM (finite element method) software packages. Fig. 2 (curve 2) shows the course of deformation predicted using LS-DYNA software package of the longer on with rectangular cross section under compression [9]. This software package is used to predict local process deviations in course of deformation that can increase spread of results thus when determining characteristics of element-model it's worth using integral characteristics, for example, relationships deformation-the amount of absorbed energy.

Based on the selected data in Fig. 2, the descriptions of individual deformation non-linear elastically plastic elements c1, c2 and c3 were made under compression of the element. Relationships were defined using variables si for the description of the deformation of the element:

[MATHEMATICAL EXPRESSION NOT REPRODUCIBLE IN ASCII] (2)

Prior to commencement of the plastic deformation, a model of elastic deformations was used. From the start of plastic deformations, calculation of the course of deformations is changed depending on the speed of process:

[MATHEMATICAL EXPRESSION NOT REPRODUCIBLE IN ASCII] (3)

where [c.sub.+] is stiffness of the element in progress of deformation (can be negative); [c.sub.-] is stiffness during kick-back (of the elastic deformation), set in the beginning of calculation for each part of the relationship force-deformation (Fig. 3).

Permanent deformations for the point A (Fig. 3) are calculated as follows:

[s.sub.pr] = [s.sup.*] - [F.sub.A]/c_, (4)

where [F.sub.A] is a force, correspondent to the point A.

Developing a more precise description of elements within deformation zone should be focussed on the last phase of the zone deformation--the final zone deformation making it totally flat. In this case, the zone becomes stiffer, and this stiffening of the zone has been simulated assuming that [F.sub.lim] is achieved when elastically deforming the rest part of the deformation zone.

[FIGURE 3 OMITTED]

Suppressive elements [k.sub.i] are used for compensation of the load dependency on the speed of deformation, which is observed in majority of cases when buckling energy absorbing closed-profile thin-walled elements [10].

The model showed in Fig. 1 can be supplemented by providing additional elements of decorative or any other nature in front of the bumper (Fig. 4). Additional elements made of rubber or foam plastic can be mounted in front bumpers of trucks to significantly reduce outcomes of car accidents during the impact of a motor vehicle with the truck [11].

[FIGURE 4 OMITTED]

For the purpose of assessing the influence of such elements on the deformation zone, some simpler (Fig. 4, a) or more complex (Fig. 4, b) are possible, in contact with the obstruction at different points of time. Consequently, additional masses are introduced into the equation system (1). This requires for formulation of relationships of force deformation of additional elements [c.sub.ijk]. As elements are usually made of foam plastic or rubber band, their descriptions are made selecting force-deformation relationships based on Types 3 and 4 from Fig. 2.

3. Results of the frontal deformation zone simulation

Values of the model presented in Fig. 1 depend on the task to be solved. To ensure maximum reliability of the results obtained, the conditions of car crash testing are strictly regulated. Consequently, in order to asses to what extent the zones in old structures satisfy modern requirements, it is necessary for testing conditions to conform to current regulations. Another condition for model development is definition of the element or group of elements under research. The fraction of the impact energy absorbed by the elements under the research within given deformation zone is distinguished. Masses of individual zones are then respectively adjusted.

The fraction of the impact suffered by the longeron was determined through analysis of NHTSA crash-test results [12]. Values [c.sub.i] were found from relationships of absorbed energy (W = W(s)) which have been determined experimentally (Fig. 5).

[FIGURE 5 OMITTED]

The characteristics of the first zone (stiffness, suppression, length) were specifically chosen to make it possible to fully stop the simulated car with the mass of 1376 kg and initial speed of 15 km/h. The characteristics of the second zone were chosen based on the findings of field experiments that have been performed on the longeron of AUDI 100 manufactured in 1990, and that of numerical models. The actual relationship of buckling force-axial shortening was approximated by the curve defined by five control points.

Particular numerical values within force-deformation relationships can be found in several different ways. Values of preliminary critical forces of longerons and other thin-walled closed-profile rods can be calculated using the analytical expression suggested by S. P. Timoschenko [2] for the calculation of critical stresses of the thin-walled cylindrical rods under compression. This equation results in condition that establishes ratio of geometric dimensions of the rod when critical stresses of the element under buckling are achieved before the material experiences its plastic deformation:

d/t [greater than or equal to] 2/[square root of (3(1-[v.sup.2]))] E/[[sigma].sub.y], (4)

where t is thickness of wall of cylinder [m]; d is mid diameter of cylinder, m; E is Young's modulus, GPa; v is Poisson's ratio, [[sigma].sub.y] is yield strength of material, MPa.

As the elements featuring effective energy absorption are deformed within the area of plastic deformations, the critical force [F.sub.kr] of the square profile pipes is found using the following expression:

[F.sub.kr] = [E.sup.*][[pi].sup.2][t.sup.3]/3(1-[v.sup.2])[b.sup.2] (5)

where [E.sup.*] = [square root of [EE.sub.t]], [E.sub.t] is a tangential module in the diagram of the material compression above the yield strength, b is width of the element under buckling [m].

Values used for the static simulation are presented in Table 1.

Results obtained through numerical simulation are presented in Figs. 6 and 7.

Fig. 6 shows dependencies of the vehicle deceleration on time, when using the model for simulation of the impact with stiff barrier under two different initial speeds.

[FIGURE 6 OMITTED]

The level of danger of the dynamic impact process can be assessed through calculation of head injury criterion (HIC) value which is used to measure the magnitude and duration of deceleration [13]. The obtained value, obviously, cannot be used to judge on damages suffered by the crew of the vehicle. HIC value is mathematically expressed as dependencies of accelerations caused within head on the maximum numerical value of the integral of time curve within a particular interval [14].

[MATHEMATICAL EXPRESSION NOT REPRODUCIBLE IN ASCII], (6)

where: [t.sub.1] and [t.sub.2] are used to define the range of time interval, within which the maximum HIC value is obtained; a is accelerations, expressed through the multiplier of a freefall acceleration g.

According to the dependencies of acceleration represented in Fig. 6, under the initial speed of impact of 30 km/h the calculated HIC value is 70. This HIC value is achieved within 0.016-0.052 s time interval. The maximum value of deceleration is 330 m/[s.sup.2].

Under the initial speed of impact of 56 km/h the maximum HIC value is 230 and it is achieved within 0.018-0.054 s time interval. The first peak deceleration value is obtained at 0.013 second, and amounts for 390 m/[s.sup.2], whereas the second peak deceleration value is obtained at 0.045 second, and amounts for 470 m/[s.sup.2].

Fig. 7 shows the distribution of the amount of energy absorbed by different zones in time.

[FIGURE 7 OMITTED]

The results obtained after the model was improved by adding the supplementary band, parameters of which are defined in Table 2, are presented in Fig. 8.

[FIGURE 8 OMITTED]

Examination of dependencies showed in Fig. 8 resulted in finding that HIC = 65 under the impact speed of 30 km/h, whereas maximum deceleration was found to be 325 m/[s.sup.2]. Under the impact speed of 56 km/h, the calculated maximum HIC value was found to be 210, whereas maximum deceleration--420 m/[s.sup.2].

As it can be observed from Figs. 6 and 8, additional deformation elements made of foam plastic or rubber introduced at the front of the vehicle contribute, although insignificantly, to the change in course of vehicle deceleration process during the impact, leading to increased duration of the process and reduced values of peak deceleration. These changes are more significant under the impact speed of 56 km/h.

Fig. 9 presents distribution of the energy absorbed by deformation zones in time, with the additional deformation elements introduced at the front of the vehicle.

[FIGURE 9 OMITTED]

As it can be observed from Figs. 7 and 9, introduction of the additional deformation elements at the front of the vehicle leads to reduction in the amount of energy absorbed by the first deformation zone. This is due to the reduction in speed of deformation of the first zone, which is reduced by the additional zone 11.

Meanwhile, the amount of energy absorbed by the second deformation zone remains practically the same as it was without any additional deformation elements.

4. Conclusions

1. Simple dynamic models were developed that enable sufficiently precise simulation of car frontal impacts and determination of the effect of changes in characteristics of deformation zones on the dynamic processes of impact.

2. The developed dynamic models can be used for assessment of the effect of additionally installed aerodynamic or different-nature multifunctional elements on the behaviour of deformation zones.

3. Research performed using dynamic models showed that introduction of additional deformation elements made of foam plastic or rubber at the front of the car, lead to changes in behaviour of deformation zones.

4. Additional elements made of foam plastic or rubber (zone 11) absorb a particular amount of energy and reduce initial speed of deformation of the subsequent deformation zone (zone 1) that in turn results in the reduced amount of the energy absorbed by the latter.

5. Additional elements made of foam plastic or rubber serve to mitigate the process of the impact. In case of simulating the impact with the barrier at the initial speed of 56 km/h, the peak deceleration value was found to be reduced by 10%, from 470 m/[s.sup.2] (no additional elements) to 420 m/[s.sup.2].

6. When assessing the level of danger of the impact process through HIC, a positive effect coming from additional plastic or rubber elements was obviously observed: under the initial speed of impact of 56 km/h and in the absence of additional elements HIC = 230, whereas in presence of additional elements HIC = 210.

http://dx.doi.org/ 10.5755/j01.mech.19.2.4170

Received May 17, 2012 Accepted April 08, 2013

References

[1.] Fenton, J. 1998. Handbook of Automotive Body Construction and Design Analysis. London, Professional Engineering Publishing, 455 p.

[2.] Timoshenko, S.; Young, D. 1968. Elements of strength of materials, Van Nostrand, 377 p.

[3.] Wierzbicki, T.; Abramowicz, W. 1983. On the crushing mechanics of thin-walled structures, Journal of Applied Mechanics 50: 727-734. http://dx.doi.org/10.1115/L3167137.

[4.] Abramowicz, W.; Jones, N. 1986. Dynamic progressive buckling of circular and square tubes, International Journal of Impact Engineering 4: 243-270. http://dx.doi.org/10.1016/0734-743X(86)90017-5.

[5.] Karagiozova, D.; Jones, N. 2001. Dynamic effects on buckling and energy absorption of cylindrical shells under axial impact, Thin-Walled Structures 39: 583610. http://dx.doi.org/10.1016/S0263-8231(01)00015-5.

[6.] Seiffert, U.; Wech, L. 2007. Automotive Safety Handbook, Warrendale, SAE International, 306 p.

[7.] Huang, M. 2002. Vehicle Crash Mechanics, London, CRC Press, 489p.

[8.] Ni, C.M.; Song, J.O. 1986. Computer-Aided Design Analysis Methods for Vehicle Structural Crashworthiness, Symposium on Vehicle Crashworthiness Including Impact Biomechanics, ASME, AMD-Vol. 79/BED Vol. 1, 125-139.

[9.] LS-DYNA Keyword User's Manual, 2006. Livermore Software Technology Corporation, 2500 p.

[10.] Karagiozova, D.; Jones, N. 2004. Dynamic buckling of elastic-plastic square tubes under axial impact--II: structural response, International Journal of Impact Engineering 30: 167-192. http://dx.doi.org/10.1016/S0734-743X(03)00062-9.

[11.] Krusper, A.; Thomson, R. 2012. Truck frontal under-ride protection--compatibility factors influencing passenger car safety, International Journal of Crash worthiness 17(2): 217-232. http://dx.doi.org/10.1080/13588265.2011.648514.

[12.] William, T.; Hampton, C.; Scheldon, L.; Jamies, R. 1999. Updated review of potential test procedures for FMVSS No. 208. Office of vehicle safety research, NHTSA. p. 122.

[13.] Anindya, D.; Umesh, B.; Clifford, C. 2008. HIC(d) Criterion and Headform Rotational Acceleration in Vehicle Upper Interior Head Impact Safety Assessment, SAE Paper No. 2008-01-0186.

[14.] Cichos, D.; de Vogel, D.; Otto, M.; Shaar, O.; Zolsch, S. 2006. Crash Analysis. Criteria description, p. 142. [online] [accessed 9 Oct.. 2012]. Available from Internet: http://www.ni.com/pdf/products/us/crash_functions_de scriptions.pdf.

J. Sapragonas *, D. Juodvalkis **, R. Makaras ***, R. Kersys ****

* Kaunas University of Technology, Kostucio 27, 44312 Kaunas, Lithuania

** Kaunas University of Applied Engineering Sciences, Tvirtoves al. 35, 50155 Kaunas, Lithuania, E-mail: [email protected]

*** Kaunas University of Technology, Kostucio 27, 44312 Kaunas, Lithuania, E-mail: [email protected]

**** Kaunas University of Technology, Kostucio 27, 44312 Kaunas, Lithuania, E-mail: [email protected]

Table 1
The characteristics of deformation zones used in calculations

Nr.   Zone 1 ([m.sub.1] = 80 kg)

      [s.sub.lim]   [F.sub.lim]    [k.sub.+]    [c.sub.-]   [k.sub.-]
          ,mm           ,kN          ,kNs/m       ,kN/m       ,kNs/m

 1        20             20           2.03         280         2.03
 2        75             20           2.03         280         2.03
 3        90             40           2.03         280         2.03
 4
 5

Nr.   Zone 2 ([m.sub.2] = 280 kg)

      [s.sub.lim]    [F.sub.lim]   [k.sub.+]    [c.sub.-]   [k.sub.-]
           ,mm           ,kN         ,kNs/m       ,kN/m        ,kNs/m

 1         10            130          6.12         700         5.65
 2        100            80           6.12         700         5.65
 3        150            130          6.12         700         5.65
 4        270            75           6.12         700         5.65
 5        360            180          6.12         700         5.65

Nr.   Zone 3 ([m.sub.3] = 1016 kg)

      [s.sub.lim]    [F.sub.lim]   [k.sub.+]    [c.sub.-]   [k.sub.-]
           ,mm           ,kN         ,kNs/m       ,kN/m       ,kNs/m

1          10            180         15.32        1500        15.32
2         100            180         15.32        1500        15.32
3         150            300         15.32        1500        15.32
4
5

Table 2

The characteristics of additional deformation zone 11

Nr.   [s.sub.lim]   [F.sub.lim]   [k.sub.+]    [c.sub.-]   [k.sub.-]
          ,mm           ,kN         ,kNs/m       ,kN/m      ,kNs/m

1         20             5           0.52         220        0.52
2         100           7.5          0.52         220        0.52